7" Angry Eye Headlight Installation Guide

Important Notes

Professional installation recommended.
Always disconnect your battery before starting.
Test Headlights prior to starting installation.

Overview:

Bushdoof Custom Headlights are engineered for easy installation using factory mounts and plug & play connections. Follow this guide for a seamless install.

What you'll need:

• Phillips screwdriver
• Trim removal tools
  
• Soldering iron or Crimp tool
• Socket set
• Electrical tape
• Zip ties
• Multimeter (optional)
• Vehicle manual (for reference)

Step 1: Remove Factory Headlights

• Ensure Bushdoof 7" Headlights are not damaged from transit & all components are there.
• You should have:
  - 2x Bushdoof 7" Angry Eye Headlights
  - 1x Demon Eye Controller + Extension Wire
  - 1x RGBW Controller + Extension Wire
  - 2x H4 Adapters
  
• Remove Grille or anything needed to remove your existing Headlights.
• Remove Headlights, isolating indicators & park lights.

Step 2: Prepare & Route Wiring

• We recommend mounting controllers out of direct weather, behind the grille, under the radiator support or behind a headlight depending on the vehicle.
  Mount the controllers closer to one side so that wiring reaches both Headlights.
  
• Plug the H4 Adapter into your H4 vehicle feed.
  
• Note the larger 2-pin plug with the brown and blue wire is polarity sensitive. Negatively switched vehicles such as Toyota Landcruiser's.
• Run the extension wires from both controllers to each Headlight location.
• You will need to locate both Indicator (+) wires and the Park Light (+) wire on one side of the vehicles feed.

Step 3: Power Controllers

• Wire in both controllers, we recommend powering both controllers from the same source, splicing them together for ease of installation.
  Power them to a full time 12V source if you want the ability to use the controllers when the vehicle is off otherwise use an ignition source for full time power.
• Splice into the Indicator & Park Light (+) wires ensuring they are properly insulated.
• If removing the factory Indicator globe, add an Load Resistor between the (+) & (-) indicator wires to prevent hyper-flashing.
• Refer to the wiring information below for Wiring Diagram.
• Ensure all connections are fused, a 7.5Ah fuse is recommended.
  

Step 4: Headlight Installation 

• Install Bushdoof Headlights, plugging in H4 adapters & controller plugs.
• Ensure all wiring is working as intended.
• Now it's time to level your new Headlights. Take note of the low beam beam output while the car is facing a wall of roughly 5-10 meters away.
• Ensure the low beam is not shining too high, as you will blind oncoming traffic.
• Use your factory headlight adjusters to match the beam angle of each headlight and set the desired height. The easiest way to do this is to park against a wall to easily see the beam angle of each light. 
• Put grille, bumper and any parts removed back on the vehicle.

Step 5: Test & Configure

• Download the App(s) below to take control of your Headlights. Ensure Location Services & Bluetooth Connections are allowed.
• For the Magic LED App, Select the SP105E Controller in the App to connect.
• For the LED Lamp App, It should automatically connect in the App after selecting the 'Search' function.
• It is recommended to drive with your Low/High beams on to dissipate any moisture out of your Headlights.
• If there are signs of excessive moisture build up or moisture has not dissipated from the Headlights after 10 days of use, please contact us.
• Please note: When connecting your controllers to the battery, they will default to automatic mode. This can be disabled in the app, allowing the headlights to operate solely from the park/indicator inputs at all times.
  
  When you'd like to display a colour, simply open the app and select any colour or mode at any time.
  
  Alternatively, the controllers can be wired to a switch, however the park and indicator inputs will not function while the switch is off.
• The park light input will always override the colour selection on the app

Wiring Diagram:

Tech Specs:

Downloads:

• Bushdoof Inner Light Control App (iOS)
  
• Bushdoof Outer Light Control App (iOS)
• Bushdoof  Inner Light Control (Android)
  
• Bushdoof Outer Light Control App (Android)
  
• Troubleshooting